[[File:NinebotMaxG2DRV148Update.png|thumb|center|200px|The update message for DRV 1.4.8 from the Segway-Ninebot app.]]
{{ Ninebot Max G2 DRV Firmware Header }}
...
2 KB (227 words) - 04:36, 24 April 2024
{{ Ninebot Max BLE Firmware Header }}
...rsion introduced downgrade restrictions similar to [[Ninebot Max DRV 1.7.0|DRV 1.7.0]].
...
1 KB (156 words) - 18:18, 9 February 2023
It can be used to configure supported scooters and flash new/custom firmware to them.
==Firmware Support==
...
2 KB (247 words) - 01:20, 18 April 2024
"Incompatible DRV firmware - change firmware or component"
...
344 bytes (46 words) - 22:53, 1 December 2021
This error is caused when the vehicle has been updated to a DRV or BLE version that has downgrade protection in place.
For the Ninebot Max/G30, this began with [[Ninebot Max DRV 1.7.0]].
...
671 bytes (112 words) - 18:17, 11 May 2024
This error is usually a firmware mismatch.
Make sure your scooter has firmware versions that work together, ex:
...
632 bytes (94 words) - 17:31, 1 December 2023
*[[Ninebot Max/G30 Firmware]]
...://joeybabcock.me/wiki/Ninebot_Max/G30_Firmware#ESC%2FDRV_Firmware DRV/ESC Firmware]
...
2 KB (312 words) - 23:15, 8 May 2024
{{ Ninebot Max BLE Firmware Header }}
...s to allow users to set the start speed, a feature that has been in Custom Firmware (CFW) for years.
...
1 KB (177 words) - 23:34, 16 December 2022
...earlier firmware/custom firmware, your base version must be [[Ninebot Max DRV 1.8.7|1.8.7]] or above. To keep the flashing ability on these generations,
...gen is ScooterHacking's [[SHFW]] or those based on [[Ninebot Max DRV 1.8.7|DRV 1.8.7]] or above.
...
3 KB (418 words) - 21:53, 24 January 2024
*[[Ninebot ESX Firmware|Ninebot ESX Firmware(ES1, ES2, ES3, and ES4)]]
...ttps://joeybabcock.me/wiki/Ninebot_ESX_Firmware#ESC%2FDRV_Firmware DRV/ESC Firmware]
...
1 KB (211 words) - 23:32, 10 September 2023
"BLE incompatible with DRV - change firmware or component"
...
576 bytes (87 words) - 04:16, 28 February 2023
You likely installed firmware on your scooter with "show battery percentage while idle" enabled.
If it bothers you you can flash stock firmware to the BLE and DRV/ESC to remove this functionality.
...
838 bytes (136 words) - 03:24, 30 January 2024
...sions like [[Ninebot Max DRV 1.8.7|DRV 1.8.7]] and [[Ninebot Max DRV 1.8.8|DRV 1.8.8]].
...r version number is now [[Ninebot Max DRV 1.6.13|1.6.13]] or [[Ninebot Max DRV 1.7.3|1.7.3]].
...
4 KB (657 words) - 04:20, 29 April 2024
You likely installed firmware on your scooter with "show battery percentage while idle" enabled.
If it bothers you you can flash stock firmware to the BLE and DRV/ESC to remove this functionality.
...
1,003 bytes (167 words) - 06:42, 26 February 2024
Regardless, this error indicates that the ESC/DRV is not able to communicate with the BMS.
A failed BMS firmware flash can also cause Error 21.
...
1 KB (237 words) - 18:51, 31 December 2021
It was based on an AT32 chip and incompatible with STM32-based Custom Firmware and STLinking.
This model can only be flashed with some types of firmware, and can only be STLinked with [[ScooterHacking ReFlasher]].
...
3 KB (451 words) - 19:28, 17 September 2023