Template:Ninebot ESX Access Internals: Difference between revisions

Template:Ninebot ESX Access Internals (view source)

Revision as of 01:36, 2 September 2023

260 bytes added , 2 September 2023

no edit summary

Joeybab3

Administrators, Swags, Bureaucrats, Administrators

3,830

edits

@@ Line 1: / Line 1: @@
-===Removing the Pole===
+Start by placing the plastic battery-ESC clip into the battery.
-Remove the 4x Security Torx T25 screws or Hex Screws that hold the handlebar in place on the pole.
+[[File:NinebotESXBatteryESCClipInPlace.jpg|thumb|center|400px|The clip placed securely onto the battery.]]
-[[File: NinebotEsxHandlebarScrews.jpg|thumb|center|400px|The handlebar screws in place.]]
+Thread the dashboard cable through the power cable on the battery.
+[[File:NinebotESXDashboardCableThreading.jpg|thumb|center|400px|The dashboard cable threaded through the battery cable.]]
+Plug in the 4-pin data line.
+[[File:NinebotESXDataCablePluggedIn.jpg|thumb|center|400px|The data cable firmly plugged in.]]
+Plug in the power cable.
+[[File:NinebotESXPowerCablePluggedIn.jpg|thumb|center|400px|The power cable plugged in.]]
+Feed the loose dashboard cable until it is mostly tight.
+Clip the ESC to the battery.
+[[File:NinebotESXBatteryESCClipped.jpg|thumb|center|400px|The esc clipped to the battery.]]
-Remove the 4x Security Torx T30 screws or Hex screws that hold the pole to the base.
+Press firmly to reinstall the dashboard cable into the channel, pulling the dashboard cable tight.
-[[File: NinebotEsxFrontPoleScrews.jpg|thumb|center|400px|The front pole screws in place.]]
+[[File:NinebotESXDashboardCableInstalled.jpg|thumb|center|400px|The dashboard cable installed in the battery channel.]]
-[[File: NinebotEsxRearPoleScrews.jpg|thumb|center|400px|The rear pole screws in place.]]
+Slide the battery and ESC into the pole.
-===Accessing the Internals===
+[[File:NinebotESXBatteryEscPole.jpg|thumb|center|400px|The assembly should slide upward into the pole.]]
-If you have an external battery, two screws hold the battery on the bracket.
+Align the charging port and insert the small screw.
-These are either security hex or regular hex.
+[[File:NinebotESXBatteryEscInPole.jpg|thumb|center|400px|The assembly should fit perfectly with the charging port lining up.]]
-[[File:NinebotESXExternalBatteryScrews.jpg|thumb|center|400px|The two screws holding the external battery on the bracket.]]
+If using an external battery, use Loctite/thread lock on the 3 holes.
-This will expose 3 more screws.
+[[File:NinebotESXBracketPrep.jpg|thumb|center|400px|Blue loctite/threadlock insures that the battery is secure and helps prevent error 42.]]
-Take care removing these screws as they strip very easily.
+Take care reinstalling the 3 bracket screws as they strip very easily.
 [[File:NinebotESXExternalBatteryBracketScrews.jpg|thumb|center|400px|The 3 easily-strippable screws.]]
-The bracket may be slightly stuck but once these 3 screws are out it can be removed.
 If you do not have a bracket then you will have three screws holding the battery in place within the pole.
@@ Line 31: / Line 45: @@
 [[File:NinebotESXInternalBatteryPoleScrews.jpg|thumb|center|400px|The 3 screws that hold the internal battery in place within the pole.]]
-You will also have a charging port cover to remove.
+You will also have a charging port cover to reinstall.
-Remove the top cover to reveal two screws holding the cover on.
+Install the two screws and the cover.
 [[File:NinebotESXChargingPortCoverScrews.jpg|thumb|center|400px|The port cover removed.]]
-Finally, one more screw holds the ESC in place on the pole.
+If you have an external battery, two screws hold the battery on the bracket.
-[[File:NinebotESXESCPoleScrew.jpg|thumb|center|400px|The final screw holding the ESC in place within the pole.]]
+These are either security hex or regular hex.
-Next comes arguably the most annoying part of the disassembly, removing the waterproofing grommets.
+[[File:NinebotESXExternalBatteryScrews.jpg|thumb|center|400px|The two screws holding the external battery on the bracket.]]
-On the top and the bottom is two grommets that are twisted in place.
+Plug in the dashboard cable to the dashboard in the handlebar.
-Press down hard with a large flathead screwdriver and twist counter-clockwise until the slots line up with the metal ridge within the pole.
+Test that the scooter still functions before continuing with assembly.
-[[File:NinebotESXInternalRubberGrommets.jpg|thumb|center|400px|Keep the grommets attached if you can.]]
+Reinstall the 4x Security Torx T25 screws or Hex Screws that hold the handlebar in place on the pole.
-[[File:NinebotESXInternalRubberGrommetsRemoved.jpg|thumb|center|400px|The parts of the grommet.]]
+[[File: NinebotEsxHandlebarScrews.jpg|thumb|center|400px|The handlebar screws in place.]]
-In some cases, pushing the rubber inner part through the plastic retainer ring will make it easier to remove.
+Reinstall the 4x Security Torx T30 screws or Hex screws that hold the pole to the base.
-Attempt to keep the wires pushed through the rubber part.
+[[File: NinebotEsxFrontPoleScrews.jpg|thumb|center|400px|The front pole screws in place.]]
-Once both are separated the whole mechanism slides easily out of the pole unless the pole has been damaged or bent.
+[[File: NinebotEsxRearPoleScrews.jpg|thumb|center|400px|The rear pole screws in place.]]
-[[File:NinebotESXInternalElectricalsRemoved.jpg|thumb|center|400px|The battery/esc internals. Here the ESC is highlighted but you want to separate it from the battery.]]
-A plastic holder clips the battery and ESC together.
-Separate the ESC from the battery and carefully unplug the 4-pin data cable and the power cable.
+Check that the scooter is sturdy and nothing is loose.